Full Description

Job DetailsJob Location: Teal Drones - SLC, UT 84115Position Summary The Mechanical Engineering Verification Test Engineer is responsible for planning, developing, and executing verification and validation (V&V) testing for complex electromechanical systems from prototype through production release. In this role, you will own the verification strategy for mechanical and mechatronic subsystems, including actuation, sensors, control hardware, and integrated systems. You will work closely with Mechanical, Electrical, Software, and Manufacturing Engineering teams to ensure designs meet functional, performance, reliability, and regulatory requirements. This role requires demonstrated hands-on experience with mechatronic systems, including PLC programming, controls integration, instrumentation, and automated test systems. You will take ownership of test architecture, develop robust test methods, and drive issues to resolution through data-driven analysis. Essential Duties and Responsibilities Own the mechanical and mechatronic verification test strategy across product platforms Develop system-level and subsystem-level verification plans, test matrices, and acceptance criteria based on product requirements Translate high-level product and system requirements into clear, traceable, and testable verification requirements Design, build, and commission test fixtures, rigs, and automated test equipment Program and maintain PLCs and control systems used in verification testing (motion control, actuation, sensors, safety interlocks, data acquisition) Integrate mechanical hardware with electrical controls, instrumentation, and software for closed-loop testing Write, review, and execute Engineering Verification Test (EVT), Design Verification Test (DVT), and Production Validation Test (PVT) procedures Develop automated test scripts and control logic to improve test repeatability, throughput, and data quality Perform structural, thermal, vibration, life cycle, and environmental testing as required Analyze test data, identify failure modes, and drive corrective actions with design teams Act as the primary point of contact for mechanical verification activities across cross-functional teams Support supplier and third-party testing, including test definition, witnessing, and result review Provide guidance on design-for-test (DFT) best practices early in the design cycle Maintain accurate documentation, test reports, and traceability within the PLM and requirements management systems Support manufacturing bring-up, end-of-line testing, and root-cause analysis for production issues Required Qualifications BS or MS in Mechanical Engineering, Mechatronics, Robotics, or related field 8+ years’ experience testing electromechanical and mechatronic systems Strong understanding of mechanical systems, tolerancing, materials, and failure mechanisms Hands-on experience with PLC programming and data acquisition systems Experience with motion control systems, actuators, motors, encoders, sensors, and safety circuits Experience developing automated or semi-automated test systems Familiarity with SolidWorks or similar CAD tools for fixture and test equipment design Experience using lab equipment for mechanical and system testing (load frames, shakers, thermal chambers, instrumentation, etc.) Knowledge of verification methodologies, requirements traceability, and structured test processes Ability to work effectively across Mechanical, Electrical, Software, and Manufacturing teams Familiarity with FMEA, root cause analysis, and reliability testing Experience supporting both R&D and production environments Additional Desired Qualifications Experience with UAVs, robotics, industrial automation, or complex electromechanical products Physical Requirements and Working Conditions Must be able to walk, stand, and navigate large indoor and outdoor facilities for extended periods of time. Ability to lift, carry, and move materials and equipment weighing up to 25 lbs on a regular basis. Use of personal protective equipment (PPE) may be required in designated areas or when performing specific tasks, in accordance with safety protocols and company policy. May be required to climb ladders, stoop, kneel, or crouch during inspections, maintenance walk-throughs, or emergency response situations. Regular exposure to facility operations including noise, dust, temperature fluctuations, and industrial equipment. Occasional off-hours or weekend work required for emergency facility responses or projects as needed Requires frequent use of a computer and other standard office equipment for documentation, communication, and coordination tasks. Background Check This position will require successfully completing a post-offer background check. Qualified candidates with a criminal history will be considered and are not automatically disqualified, consistent with federal and state law. EEO and ITAR/EAR Work Authorization Disclosure Red Cat Holdings provides equal employment opportunities (EEO) to all employees and applicants for employment and prohibits discrimination and harassment of any type without regard to race, color, religion, age, sex, national origin, disability status, genetics, protected veteran status, sexual orientation, gender identity or expression, or any other characteristic protected by federal, state or local laws. This position requires direct or indirect access to hardware, software, technology or technical data controlled under the International Traffic in Arms Regulations (ITAR) and the Export Administration Regulations (EAR). Successful candidates for positions subject to ITAR/EAR restrictions must provide proof of U.S. Citizenship or Permanent Residence and must not require sponsorship for export-restricted work authorization. E-Verify The company participates E-Verify ensure eligibility for employment and compliance with Right to Work rules. Compensation: Salary plus generous annual equity package and potential bonuses. Qualifications